July 21, 2014
Air conditioning Units, Split system
Select an unobstructed area on the interior wall surface to install the interior air conditioner.
- Eliminate sunlight and heat sources.
- Avoid areas where gasoline may leak or in which oil mist or sulphur is present.
- The interior unit requires at least 6" (15 cm) of available room surrounding its top and edges. The unit must also be installed at least 7 foot (2.13 m) over the ground.
- Install the system at least 3.3 feet (1 m) from antenna, energy or connecting lines that are employed for tv, radio, home security methods, intercoms or telephones. The electrical sound from the sources could cause working problems for your ac.
- The wall surface ought to be strong enough to keep the weight of product. You may need to construct a wood or metal framework to provide included support.
- Contain the mounting dish from the wall for which you would you like to install the indoor device.
- Use a level to make sure the plate is actually horizontally amount.
- Drill holes into the wall at proper spots to affix the plate towards wall surface.
- Insert synthetic anchors to the holes. Secure the dish towards the wall surface with tapping screws.
- Find a very good area when it comes to hole into the external on the basis of the orifice in the mounting bracket. Opt for the size of the pipe in addition to length that it has to visit attain the exterior product.
- Drill a hole that's 3" (7.5 cm) in diameter through wall surface. The hole should slope downward toward the exterior to make sure adequate drainage.
- Insert a flexible flange to the opening.
- Lift the unit’s front panel and take away the address.
- Be certain the cable cables are attached to the screw terminals. In addition, make sure that they fit the drawing that comes with the machine.
- Operate the piping through the indoor unit toward the opening drilled through wall surface. Minimize bending to make sure that the system performs well.
- Cut an amount of PVC pipeline 1/4" (6 millimeters) shorter as compared to size between interior and external wall surfaces.
- Position the pipe cap regarding the interior end associated with the PVC pipeline. Insert the pipeline to the hole in the wall.
- Bind the copper pipes, the power cables and strain pipe and electric tape. Put the strain pipe on base assuring a totally free flow of liquid.
- Protected the pipe to your interior product. usage 2 wrenches, in opposite directions, to tighten up the connection.
- Get in on the liquid drainage pipeline towards the indoor unit’s base.
- Operate the certain pipes and cables through the gap into the wall. Ensure that the drainage pipe enables water to deplete in a suitable destination.
Secure the indoor device towards the installation plate by pressing the system contrary to the installation dish.
Component 2Install the Outdoor Condenser
- Pick the best location to put in the outside device.
- The outside unit’s place has to be away from any heavily trafficked, dusty or hot places.
- The outdoor device requires 12" of area surrounding its border to make certain appropriate functioning.
- Lay the tangible pad on the ground and also make sure it really is amount. The pad is sufficient so that the condenser will stay over the standard of winter months snows.
- Set the outside condenser together with the pad. utilize rubberized cushioning under the device's foot to minimize vibration.
- Make sure that no antenna of a radio or tv is within 10 foot (3 meters) of this outside condenser.
- Link the electric wires.
- Get rid of the cover.
- Make reference to the unit’s wiring drawing and also make certain the cable wires tend to be connected once the drawing proposes. After the maker's directions for wiring is essential.
- Fasten the cables with a cable clamp and change the address.
- Protected the pipelines’ flare peanuts to the corresponding pipelines on outside product.
Part 3Finish the Split System Ac Installation
- Bleed the atmosphere and humidity from the refrigerant circuit.
- Eliminate the limits from the 2-way and 3-way valves and from solution slot.
- Link a vacuum pump hose pipe toward service port.
- Change the cleaner on until it reaches a complete vacuum of 10mm Hg.
- Close the low stress knob after which switch off the cleaner.
- Testing all of the valves and bones for leaks.
- Disconnect the machine. Swap the solution port and hats.
- Wrap the joints of this piping with insulating covering and insulating tape.
- Affix the piping into wall surface with clamps.
- Seal up the opening when you look at the wall surface making use of growing reboundable foam.
Share this article
April 25, 2014
January 30, 2016
May 26, 2016